[Click on each image to Zoom]

SAFTI-TRAX™ is a unique system designed specifically for compliance with the Americans with Disabilities Act (ADA) requirements for detectable warnings on curb ramps and rail platforms.

PRODUCT FEATURES

• SAFTI-TRAX™ is a permanent retrofit system that is applied directly to clean dry surfaces without the need of specialized labor or machinery. It is therefore not labor intensive and not costly to apply.
• SAFTI-TRAX™ incorporates resilient rubber domes, made exclusively by COTE-L Industries, with an over coating of our new and unique Durabak™, a one-part, non-slip, totally flexible polyurethane safety coating.
• SAFTI-TRAX™ enjoys all the unique characteristics of its major component, Durabak™. It is extremely durable, waterproof, repairable, and corrosive resistant. It bonds to concrete, wood, primed or sound-coatinged metal surfaces, fiber glass, and most other surfaces. And Durabak™ comes in a wide range of colors.
• SAFTI-TRAX™ will conform to any surface irregularity, facilitating a virtually faultless application.
• SAFTI-TRAX™ is not only flexible, but resilient, as specifically required by the ADA.
• SAFTI-TRAX™ is easy to clean and easy to repair.
• The total cost per square foot of SAFTI-TRAX™ with Durabak™, for materials and labor, is significantly less than other products because of its ease of application.
  

1. Durabak™ totally flexible one-step slip-resistant coating
2. Accelerator packets
3. COTE-L's special stipple rollers
4. Truncated rubber domes attached to 2'x2' or 2'x4' plastic sheets in A.D.A. specified matrix.

1. Xylene, for cleaning surface and for thinning of Durabak™, if necessary
2. Heavy duty rubber gloves
3. Masking tape
4. coating roller pan

Click on an image below for larger detail.

Procedure

---

Please read all instructions carefully before proceeding.

1. Clean surface as specified in Durabak™ instructions. New concrete should be fully cured and cleaned with a concrete cleaner. Remove all residue. Old concrete should be cleaned with Muriatic Acid or a citric cleaner. Again, remove all residue. Surface should then be thoroughly dried. Old or new concrete should be wiped finally with Xylene immediately before the first coat of Durabak™ is applied.

2. Lay out SAFTI-TRAX™ plastic sheets with truncated domes for sizing. Be sure to leave white paper release sheet in place underneath domes. If required, cut sheets to size with scissors. When more than one sheet is to be installed in a single area, be sure to line up the alternating rows of domes correctly.
3. Mask off area to be covered by SAFTI-TRAX™
4. Place plastic sheet with domes still attached outside work area.
5. Add 1 quart-packet of accelerator per quart (or 1 gallon-packet per gallon) of Durabak™ and mix can thoroughly and frequently, preferably with an electric mixer. Apply one coat of Durabak™ onto masked-off area. Do not coat an area larger than one sheet at a time as the domes will need to be placed on wet Durabak™ within 10 minutes (see #7)
   NOTE: After each coat, close can tightly. Wet stipple roller with Xylene and cover with plastic bag so roller will not dry out. If application is by spray gun, clean spray gun between coats.
6. Lift plastic sheets (with domes attached) and remove the white, bottom release sheet from SAFTI-TRAX™ truncated domes.
7. While the Durabak™ is still wet (within 10 minutes of application), lay domes (with top plastic sheet still attached) in place on wet surface. Without removing plastic sheet, lightly press domes down with a small board to ensure that the bottom of all the domes are making contact with the wet Durabak™. If surface is uneven, you may need to press some individual domes down by hand.
8. Do not remove plastic sheets from the domes for two to three hours or more, until the domes are solidly attached to the Durabak™. Lighter colors, such as Safety Yellow, may require 4-7 hours or more, depending on climatic conditions.
9. Gently and slowly peel off top plastic sheet parallel to surface, holding the individual domes down with one hand while peeling the sheet back with the other, being careful not to dislodge domes. (You may use a razor blade to slice the plastic sheet into smaller strips for easier removal.) If a dome should become dislodged, apply some Durabak™ to the bottom of the dome and press firmly back into place.
10. Apply coat of Durabak™ over truncated domes and entire masked-off surface, making sure Durabak™ covers the outside base of the domes. Roll in several different directions to ensure complete coverage.
11. When the last coat of Durabak™ has become touch dry, repeat step 10 with two more coats, allowing each coat to dry before applying the next one.
12. Remove masking tape and let SAFTI-TRAX™ dry. If tape is not removed promptly and is sticking to the Durabak™, cut along edge with a razor knife and then remove tape.
13. SAFTI-TRAX™ surface can be walked on in 6 to 12 hours in conditions of average humidity. For special circumstances, average walking time can be reduced. For information, contact authorized SAFTI-TRAX™ representative.